Longtime cannabis advocate Rick Simpson has done a great deal in his long career to help advance cannabis therapies. Fortunately, we’re here to share more of his work.
In his long career, Simpson has treated patients will all types of conditions including, but not limited to, cancer, AIDS, arthritis, multiple sclerosis, diabetes, leukemia, Crohn’s disease, depression, osteoporosis, psoriasis, insomnia, glaucoma, asthma, burns, migraines, regulation of body weight, chronic pain, and mutated cells (polyps, warts, tumors).
The documentary below tells a great deal more about Simpson’s story.
Check out Rick Simpson’s hash oil recipe. Start with an ounce of dried herb, which will produce 3-4 grams of oil. (A pound of herb dried yields roughly two ounces of oil.)
IMPORTANT: These instructions are directly summarized from Rick Simpson’s website. Be VERY careful when boiling solvent off [solvent-free option], the flames are extremely flammable. AVOID smoking, sparks, stove-tops, and red hot heating elements. Set up a fan to blow fumes away from the pot, and set up in a well-ventilated area for whole process.
- Place the completely dry material in a plastic bucket.
- Dampen the material with the solvent you are using. Many solvents can be used [solvent-free option]. You can use pure naphtha, ether, butane, 99% isopropyl alcohol, or even water. Two gallons of solvent is required to extract the THC from one pound, and 500 ml is enough for an ounce.
- Crush the plant material using a stick of clean, untreated wood or any other similar device. Although the material will be damp, it will still be relatively easy to crush up because it is so dry.
- Continue to crush the material with the stick, while adding solvent until the plant material is completely covered and soaked. Remain stirring the mixture for about three minutes. As you do this, the THC is dissolved off the material into the solvent.
- Pour the solvent oil mixture off the plant material into another bucket. At this point you have stripped the material of about 80% of its THC.
- Second wash: again add solvent to the mixture and work for another three minutes to extract the remaining THC.
- Pour this solvent oil mix into the bucket containing the first mix that was previously poured out.
- Discard the twice washed plant material.
- Pour the solvent oil mixture through a coffee filter into a clean container.
- Boil the solvent off: a rice cooker will boil the solvent off nicely, and will hold over a half gallon of solvent mixture. CAUTION: avoid stove-tops, red hot elements, sparks, cigarettes, and open flames as the fumes are extremely flammable.
- Add solvent to rice cooker until it is about ¾ full and turn on HIGH heat. Make sure you are in a well-ventilated area and set up a fan to carry the solvent fumes away. Continue to add mixture to cooker as solvent evaporates until you have added it all to the cooker.
- As the level in the rice cooker decreases for the last time, add a few drops of water (about 10 drops of water for a pound of dry material). This will help to release the solvent residue, and protect the oil from too much heat.
- When there is about one inch of solvent-water mixture in the rice cooker, put on your oven mitts and pick the unit up and swirl the contents until the solvent has finished boiling off.
- When the solvent has been boiled off, turn the cooker to LOW heat. At no point should the oil ever reach over 290˚ F or 140˚ C.
- Keep your oven mitts on and remove the pot containing the oil from the rice cooker. Gently pour the oil into a stainless steel container
- Place the stainless steel container in a dehydrator, or put it on a gentle heating device such as a coffee warmer. It may take a few hours but the water and volatile terpenes will be evaporated from the oil. When there is no longer any surface activity on the oil, it is ready for use.
- Suck the oil up in a plastic syringe, or in any other container you see fit. A syringe will make the oil easy to dispense. When the oil cools completely it will have the consistency of thick grease.
Enjoy – and let us know how it works for you! Thanks to The Mind Unleashed for the tips!
If you enjoyed this article or learned something new, please don’t forget to share it with others so they have a chance to enjoy this free information. This article is open source and free to reblog or use if you give a direct link back to the original article URL. Thanks for taking the time to support an open source initiative. We believe all information should be free and available to everyone. Have a good day and we hope to see you soon!
Please follow and like us: